How to Set Up Netgear as a Repeater

Video of the Day

How to Turn a Belkin WiFi Router Into a Repeater
Connect your computer to the LAN or wired port of the main router. Remove any entries that are located in the "Port Forwarding" section. As others have mentioned, most consumer-grade routers do not have Wireless Repeater capability in their firmware. I've used a dedicated hardware repeater before and ultimately replaced it with a hardwire run. If you know these details, enter them. By using our site, you acknowledge that you have read and understand our Cookie Policy , Privacy Policy , and our Terms of Service.

Related Articles

How to Use a Router as a Repeater

The address should be changed so that it is not the same as the main router on the network, or any other network devices. If the main router on the network is set to use Disable the router's DHCP server. This setting should be on the same page as the IP address, but each router is a little different. When the router is operating normally, this server assigns an IP address to every device that is connected to it.

Because this router will be used as a repeater only, the IP addresses will now be handled by the main router on the network. Turn off the DNS server, if it is activated. This function will be taken over by the main router, or by the ISP that provides the Internet connection to your location. Disable any firewall that is built into the router. Usually, this can be done in the "Security" section, and it may require you to alter several settings, depending on the make and model of the router.

Remove any entries that are located in the "Port Forwarding" section. On some routers, this may be referred to as "Applications and Gaming," and it allows certain programs to have less-restricted access to the Internet.

Set the operating mode switch to "Gateway" or "Switch" if such a setting is available. In addition, if the router is a wireless router and has the appropriate settings, disable the wireless access or set it to function as an access point only. Save the settings as necessary on each page, and reboot the router. After the router boots back up, the changes should allow it to act more or less as a simple repeater.

How to set up a Wireless Bridge between two Belkin routers. Belkin routers had this capability since the software settings changed to bridging. Setting up a Wireless Bridge allows you to expand the range of the wireless network broadcasted by your main wireless router. This article will describe the steps needed to do so. Connect your computer to the LAN or wired port of the main router.

If the default IP address doesn't work, check your router's IP address. For instructions, click here. You may also enter http: You will then be directed to the router's web-based setup page similar to the one below.

If you want to change or configure any settings, you will need to log in with your router's administrator password by clicking on Login at the top right corner of the page. If you haven't set up a password for your router, leave the field blank then click Submit. Therefore, interoperability between You should have successfully set up Wireless Bridge between your two 2 Belkin routers now. From what I see in the manual this router probably won't do what your hopping for.

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site the association bonus does not count.

Would you like to answer one of these unanswered questions instead? Home Questions Tags Users Unanswered. Can I use my Belkin router as a repeater? I can't use the other wireless router for anything other than broadcasting straight from the modem parents are paranoid about anything technological. I can't run ethernet to the second router due to the layout of the house. Thanks so much for the help everyone--if I'm being vague, tell me! Tried to read the manual? Yep, I've tried looking at the manual here , but it seems more like a getting started guide than an actual manual--there's not much about any specific configuration options.

Can you define "repeater"? According to this link a repeater is something that functions as an access point.

Your Answer

Leave a Reply

If the main router on the network is set to use , the router that will be used as a repeater should use a higher number, such as or , depending on how many devices are on the network. This result is through the modified Linksys WRT54G ver. 6 router about 10 feet away, connected as a repeater to the Buffalo router downstairs, and then tested again through Toronto. There is, as you can see, a download speed difference, and if I'd been using my Wireless N modem, it might be even more severe. You can set up a spare router as a repeater to boost your Wi-Fi signal beyond the reach of your current router. This won't work for everyone, but if you do have an old router sitting in a cupboard or drawer, you might be able to save money compared to buying the latest mesh network systems such as Google Wifi and BT Whole Home Wi-Fi.